Spun Bonded PolyPropylene Filter Cartridge ventilation experiment that needs to be processed in ventilation experiments. After the glass reinforced fans are pressed into the intake section of the purification tower, the absorption liquid of vertical upward and the spray section neutralizes react to reduce the concentration of the exhaust gas. Then continue to enter the filler section. The exhaust gas rolled in the plastic ball and then neutralized with the absorption liquid. After further reduction of the concentration of the exhaust gas, enter the dehydrationer segment, remove the droplets, and the purified gas is discharged at the atmosphere. According to the determined analysis, the purification rate of sulfuric acid mist can reach 93%, the purification rate of nitric acid can reach 90%, and the purification rate of the hydrochloric acid atomic acid can reach 98%.

The high -concentration of the glass fiber reinforcement acid fog purification tower has small resistance, provincial energy consumption, low noise, and high treatment efficiency. It can treat hydrogen chloride (HCL), fluoride gases (HF), ammonia (NH3), sulfate fog (H2SO4), chromic acid mist (CRO3), cyanide acid gas, (HCF), alkaline steam (NAOH), hydrogen sulfide gas (H2S) and other new purification tower. It has high purification efficiency, compact structure, small area, corrosion resistance, resistance to resistance, resistance The characteristics of good aging performance and light weight. It is suitable for emitting a certain concentration of corrosive acid mist gas, which is mainly used for chemical, electronics, hospitals, colleges, research centers and other places.

The structure of Spun Bonded PolyPropylene Filter Cartridge

The acid mist purification tower is a cylindrical structure. The whole tower consists of three parts, namely storage, air intake, spray, dehydration, and gas pump. The pump resistance is installed on the outside. Put in spray.

The acid mist purification tower is an integrated formation of the FRP, with compact structure, corrosion resistance, high temperature resistance, smooth appearance;

Water removal part: Plastic isolation isolation to produce water and gas separation;

Water spraying department: High -pressure water spraying produces fog, which is divided into two sections to expand contact treatment and improvement function;

Filling materials: sea urchin type, PP quality integrated molding;

The circulating water sink needs to have anti -spill ports, 50mm water level overflow emission pipes;

Observation window: 5mm thick and transmitted acrylic board system;

Automatic water adding device: automatic control type of floating ball liquid;

Adding pump: Use 22L/h to resist the quantitative pump.

In the era of increasingly developed industries, the exhaust gas purification tower plays a vital role. It can handle the exhaust gas discharged by the industry and can play an important role in air purification. If there is no exhaust gas purification tower, you dare not imagine how much industry will become. So, how much do you know about the installation and maintenance knowledge of the exhaust gas purification tower?

Users carry out concrete infrastructure according to basic data; equipment should be installed on the basis of concrete above 100 % higher than the ground; supporting pipelines, valves, etc. must be supported by separate support, and should not be fixed on the tower equipment; pay attention to protecting the equipment during installation. No Damaged body and exposed parts. When the pagoda flange is connected to the external flange, the correct method should be adopted. Do not force it to avoid cracking the flange. The flange pads must not use steel pads, which can be used for corrosion -resistant oil -resistant rubber pads. After the equipment is installed, it can be used for recycling with water. Normally running without running, dripping, leakage, pluggedment.

In addition, in order to ensure the normal operation of the tower equipment, a special person must be responsible for management. It should be regularly check whether the ventilator and pump operation is normal, whether the spray pipe and the trachea are unblocked, whether the liquid level is normal, and whether the hydrating floating ball switch is normal. Whether the concentration of the gas liquid is within the specified range, etc. If the problem is found, it should be resolved in time.

Knowing the scientific installation and maintenance measures of the exhaust gas purification tower, there is a lot of profit but no harm, it can extend its life span and improve its performance.

spun bonded polypropylene filter cartridge https://www.kaisenfilter.com/High-Efficiency-99-9-Spunbonded-filter-cartridge.html